ATTRES 001 1/32 Beardmore engine primer cups x 6
ATTRES 002 1/32 Mercedes engine priming cups x 6
Mastered and cast by Ron Kootje
ATTRES 003 1/32 set Spandau shell shutes (Fokker DR1 type)
As seen on von Richthofen's final DR.I (not common to all DR.I's - check your references)
Mastered and cast by Ron Kootje
ATTRES 004 1/32 Fokker DR.I/DVI cowling
Modelled accurately for the first time!
Replacement for the Roden 1/32 offering, requires small amount of sanding of the kits "chin" to meet the lower edge.
A dedicated P/E set for firewall and inspection panel also available
https://www.aviattic.co.uk/photo-etch.html
Designed by Richard Andrews
Mastered by Gerry Mos, Ron Kootje and Auke Elsinga
Cast by Ron Kootje
Requires cutting from casting block and holes drilled out.
Prime and fine sand before paint.
ATTRES 008 1/32 Gotha propeller hubs and backplates (x2)
ATTRES 009 1/32 German C and G types (Gotha, AEG etc) weighted wheels x 2
ATTRES 011 1/32 WW1 German fuel cart (small)
Download PDF instruction leaflet - kindly supplied by Dave Hooper
Originally mastered for Aviattic by Szymon Grzywocz
Re-mastered by Ron Kootje and made possible by Fusion 360.
|
Download instruction PDF!
|
| ||
ATTRES 015 1/32 "Peach Basket" seat and cushion for Nieuport types
Mastered and cast by Ron Kootje
ATTRES 016 1/32 German Siemens Halske SHIII 11 cylinder engine resin and p/e kit
Eleven cylinder engine that would have made a great difference in the air war had it not been for the lack of suitable lubricant oil...
Used in the Siemens Schuckert DIII and IV, Pfalz DR1 and DVIII as well as many other experimental types
Resin and photo etch parts
CURRENTLY UNAVAILABLE
ATTRES 018 1/32 WW1 German large Fuel Cart (Upright) - masters by Simon Grzywocz
Of the type that re-fuelled the "G" and "R" type aircraft, Gothas, AEG, Staakens etc
Originally mastered for Aviattic by Szymon Grzywocz
Re-mastered by Ron Kootje and made possible by Fusion 360.
Download PDF instruction leaflet - kindly supplied by Dave Hooper
Cast by Ron Kootje
|
Download instruction PDF!
|
| ||
ATTRES 021 1/32 WW1 RFC/RAF Fuel Cart
Originally mastered for Aviattic by Simon Grzywocz
Re-mastered by Ron Kootje and made possible by Fusion 360.
Cast by Ron Kootje
|
Download instruction PDF!
|
| ||
ATTRES 022 WW1 German Fokker DVII seat and cushion
Modelled accurately for the first time - the distinctive "flare" sided Fokker type aircraft seat, with cushion cast separately
Scaled for the DVII and EV from Achim Engels (Fokker archive based) drawings, this also works with the Roden F.I and Dr.I but is slightly larger than the new Meng/WNW DR.I kit version.
ATTRES 023 1/32 Spad XIII 65mm tyre wheel (pair)
Mastered and cast by Ron Kootje
ATTRES 027 Gaspatch 1/32 Vickers "Balloon" gun x 1 (only) - for Spad XIII
Item is a Gaspatch product, normally sold in pairs from
www.gaspatch.com
ATTRES 033 1/32 "Stripped" rudder for Fokker DR.I and DVI
3d printed to order, designed by Gerry Mos as a replacement for Roden kit part should you wish to model a damaged or wrecked machine, or simply a part cut-away!
Frame and zig-zag bracing was linen wrapped - try simulating or part covering with Aviattic German linen decals over white-primed metal foil....
ATTRES 034 1/32 Fokker DR.I/F.I/DVI rudder (for Roden kits)
Designed by Richard Andrews and Gerry Mos
Cast by Ron Kootje
A more accurate rudder for the Roden kits - just add P/E control horn and hinges from the Aviattic set or kit parts.
ATTRES 037 1/32 Fokker EV/DVIII cowling (for Mikro mir/Avis kit)
Designed by Richard Andrews, Gerry Mos and Auke Elsinga
Cast by Ron Kootje
Modelled accurately for the first time!
A dedicated P/E set for firewall and inspection panel is also available
https://www.aviattic.co.uk/photo-etch.html
OUT OF STOCK
ATTRES 032 1/32 Fokker F.I prototype cowling
Replacement for the Roden 1/32 offering, requires small amount of sanding of the kits "chin" to meet the lower edge.
Modelled accurately for the first time!
The dedicated P/E set for lower "lip", firewall and inspection panel is essential to get the correct "look" to the distinctive F.I prototype cowling
https://www.aviattic.co.uk/photo-etch.html
Designed by Richard Andrews
Mastered by Gerry Mos, Ron Kootje and Auke Elsinga
Cast by Ron Kootje
ATTRES 038 Ltd Edition "Cap'n Eddie" Rickenbacker Ansaldo Balilla set (resin and p/e)
Includes suitcase which was tied to the wing struts as Rickenbacker toured around the States post war - and set a new world speed record!
Additional fuel tank "sump" and length of brass for connection rod and p/e additional louvres for the forward starboard cowling.
ATTRES 041 Fokker DVII OAW built "early" production cowling panel set for WNW kit
Converts an "early" Wingnut Wings Fokker DVII to OAW configuration.
I recommend downloading the instruction manuals from the various WNW DVII kits from their still-functioning website.
1) Replicated kit part J10
2) Axle wing and chin cowling fasteners and bolts.
Parts replicating original WNW parts have been CAD drawn, amended where necessary and not "copy" cast.
3d printed parts require careful cutting from build trees and cleaning up with a file.
They are ready to prime and glue using CA or 2-part contact adhesive.
Instructions included for use of existing kit parts on sprue "L".
ATTRES 042 Fokker DVII OAW built "mid" production cowling panel set for WNW kit
Converts an "early" Wingnut Wings Fokker DVII to OAW configuration.
I recommend downloading the instruction manuals from the various WNW DVII kits from their still-functioning website.
1) Replicated kit parts J4, J5, J10, J14, J16, J17
2) Starboard fuselage panel with one louvre in triangular inspection panel
3) Port fuselage panel with one louvre in triangular inspection panel
4) Axle wing and chin cowling fasteners and bolts.
Parts replicating original WNW parts have been CAD drawn, amended where necessary and not "copy" cast.
3d printed parts require careful cutting from build trees and cleaning up with a file.
They are ready to prime and glue using CA or 2-part contact adhesive.
ATTRES 043 Fokker DVII OAW built "late" production cowling panel set for WNW kit
Converts an "early" Wingnut Wings Fokker DVII to OAW configuration.
I recommend downloading the instruction manuals from the various WNW DVII kits from their still-functioning website.
1) Replicated kit parts J6, J7, J10, J14, J18, J21
2) Axle wing and chin cowling fasteners and bolts.
Parts replicating original WNW parts have been CAD drawn, amended where necessary and not "copy" cast.
3d printed parts require careful cutting from build trees and cleaning up with a file.
They are ready to prime and glue using CA or 2-part contact adhesive.
ATTRES 046 Fokker DVII OAW built "mid" production Jasta 65 field-mod cowling panel set for WNW kit
Converts an "early" Wingnut Wings Fokker DVII to OAW configuration.
I recommend downloading the instruction manuals from the various WNW DVII kits from their still-functioning website.
Jasta 65 machines often flew with their upper engine cowlings removed to permit air-cooling of the volatile phosphorus ammunition.
The port upper panel may have been fixed over the lower one to eliminate in-flight "flutter" and has been noted on other machines.
This type of modification applies to "Seven Swabians" and "U10" at least..
1) Replicated kit parts J16
2) Starboard fuselage panel with one louvre in triangular inspection panel
3) Port fuselage panel with one louvre in triangular inspection panel
4) Port top panel overlapping lower panel
5) Axle wing and chin cowling fasteners and bolts.
6) Flare guns, flare racks set
Parts replicating original WNW parts have been CAD drawn, amended where necessary and not "copy" cast.
3d printed parts require careful cutting from build trees and cleaning up with a file.
They are ready to prime and glue using CA or 2-part contact adhesive.
ATTRES 052 (1/32 for Meng kit) Fokker F.I/DR.I replacement panel w/hatch opening
Intended for use with the p/e hatch on fret ATTPE 014.
Directly replaces kit part.
Requires careful cutting from build "trees" and washing in mild detergent before priming and painting.
Access panel is seen hanging down for maintenance in only a couple of period photographs.
3d CAD art by Mike Swinburne.
ATTPE 015 (1/32 for Meng kit) Replacement Fokker F.I/DR.I 3-D printed fuselage panel PLUS etched fret ATTPE014
Special offer bundle for those wishing to portray the fuselage access panel "open".
CAD panel design by Mike Swinburne
Etch designed by Richard Andrews and Ron Kootje